Best Drive Gears 2026

Advertising Disclosure

Last Updated - 03.02.2026

Best Choice

01

iMetrx

IMETRX Dual Drive Gear Extruder v3.0 Bowden Extruder Gear for Prusa i3 Anycubic Mega Creality Ender 3 V2 Pro Series

Show more
9.8

Exceptional

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Upgrate 1: Dual gear extruder v3.0 change the fitting to pneumatic fitting, users can easily replace the pneumatic fitting or gear after long use, which extend the life of the extruder.
Update 3: make a chamfer on the surface to prevent the dual drive extruder v3.0 from colliding with the rods.
Update 2: add an additional attachment in the Bowden extruder, which can help the filament load more fluidly and reduce the abrasion of the filament.
Package includes: dual drive extruder V3.0 x 1 piece
Fits almost all 3D printers with remote drive extruder. If you need directly, you may need to print a new fitting to connect the extruder gear to the hotend

19,99 €
02

Redrex

Redrex Dual Gear Ender 3 Extruder with Nema 17 Stepper Motor Upgrade Kit ONLY for Creality Ender 3 V2, Ender 3 Pro, Ender 3 Neo Series, Ender 5 Series, Ender 7, CR6 SE, CR10 3D Printer TPU Supported

Show more
9.7

Exceptional

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Upgraded idler gear design: this intermediate wheel is equipped with two washers on both sides, so that the sharp gear does not drive against the bottom of the arm or chews it.
Kindly reminder: Please calibrate the E levels from 100 to 139; please lubricate the gears before first use; for 3D printer with filament detector, please print the model to increase the filament detector to make it to the same height
High torque motor: the Nema 17 stepper motor offers 1A 40 Ncm/57 g.cm^2 in holding torque, which helps improve the stability of the motor. Note: for non-creality users, please exchange the motor wire sequence to make it turn forward instead of backward
Double gear extrusion mechanism: the filament is gripped much more firmly with less deformation thanks to the double drive, so it does not jam so much in the pipe, nozzle or hotend
Application: This all-metal extruder with double drive and motor kit is compatible with Ender 3, Ender 3 V2, Ender 3 Pro, Ender 3 Neo, Ender 3 V2 Neo, Ender 3 Max Neo, Ender 5, Ender 5 Pro, Ender 5 Plus, Ender 7, CR6 SE, CR10 series, Vox. 3 D printer. Not suitable for Anycubic or Elegoo or other brands 3D printers

18,98 €
03

POLISI

1 Set 3D Printer MK3 Drive Gear Extruder Dual Gear Kit DriveGears Extrusion Wheel for Upgrade Prusa i3 MK2/MK2S/MK2.5 3D Printer

Show more
9.5

Excellent

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Extruder Dual Gear for Prusa i3 MK3
Drive Gear Kit for Upgrade MK2/MK2S/MK2.5 3D Printer
3D Printer Drive for Prusa i3 MK3

7,09 €
Value for Money

04

VOANZO

VOANZO 3D Printer Extruder Dual Gear MK2 and MK3 Parts Drive Gear Kit Gears Extrusion Wheel for DIY Prusa i3

Show more
9.3

Excellent

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Pulley bearings replace the needle bearings, which can be easily damaged. The new bearings do not wear out in the gearbox during work
Nickel plating can prevent rust and make gears with longer life and better lubrication
Dual drive gears are made of hardened steel material with a hardness of 60 HRC and a high-precision bore of 5 mm.
Compatible with CR10S PRO DDB Extruder Prusa i3 MK3 MK2/MK2S/MK2.5 MK3S+ 3D Printer
2 x tyre levers

5,99 €
05

UniTak3D

UniTak3D Dual Drive Extruder Gear Replacement Stainless Steel Extrusion Wheels for Prusa i3 MK2/MK3, for Ender 3 V2, for Ender 3 Pro, for Ender 3, for Ender 5 Series, for Wanhao D9, for Anet E10, for

Show more
9.2

Excellent

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

【Smooth Operation】The teeth are sharper and wider to avoid filament slipping, and double gears are closely matched with the shaft and have high concentricity.
【Precise Machining】: Dual drive gears are precision machining that improves the grip of all 1.75mm filament materials.
【Material】The double gears are made of high quality 303 stainless steel, which greatly improves durability and reliability.
Easy installation: this double gear set is quite easy to install and fits well with dual drive extruder or its clones.
Application: the drive gear extruder replacement fits dual drive extruder and metal gear extruder

10,98 €
06

MMOBIEL

MMOBIEL Pack of 5 40 Teeth Brass Extruder Drive Gear Compatible with Creality 3D Printer Ender 3 V2 / 3/3 Pro / 5 / CR-10 / 10S 20/20 Pro

Show more
9.1

Excellent

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Quality product from MMOBIEL: every part is checked before shipping! Item is available immediately!
Package includes: 5 x brass pulley wheel with 40 teeth; 1 x Allen key
HIGH QUALITY MATERIAL Made of high quality brass, which is corrosion and rust resistant, very durable. These brass pulleys are known for their sturdy use with large load capacity. They improve the efficiency of your 3D printer.
EASY TO USE Easily replace your old or worn out drive timing pulley. Use the included Allen key to loosen the Allen screws on the old pulley. If the screw is loose, remove the pulley and insert the new pulley. Tighten the screw.
Compatible with Creality 3D Printer Ender 3 V2/ Ender 3/ Ender 3 Pro/Ender 5/ CR-10/10S 20/20 Pro and most other 3D printers

8,79 €
07

ZkeeShop

ZkeeShop 5pcs DRV8833 2 Channel H Bridge Motor Drive Module 1.5A DC Gear Motor Driver Board

Show more
8.9

Very Good

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

VCC: 3-10 V
ULT PIN:mode set.Low level is sleep mode
OUT3,OUT4:2-channel H-bridge controlled by IN3/IN4
OUT1,OUT2:1-channel H-bridge controlled by IN1/IN2
EEP PIN:Output protection.Default no need to connect.

9,99 €
08

Redrex

Redrex Dual Gear Extruder Ender 3 Metal Drive Feeder Upgrade for Ender 3 V2, Ender 3 Pro, Ender 3 Neo Series, Ender 5 Series, CR10, Voxelab Aquila 3D Printer (Motor Shaft > 21.5 mm) TPU Supported

Show more
8.7

Very Good

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

【Friendly reminder】: please calibrate the E levels from 100 to 139; Please lubricate the gears before first use; For 3D printer with filament detector, as the height of our double gear extruder may differ from the original, please print the model to lift the filament detector so that they are at the same height;
Upgraded intermediate gear design: this intermediate gear is equipped with two washers on both sides, so that the sharp gear does not drive against the bottom of the arm or chews it.
Spring adjustable: The extrusion spring tension can be adjusted by tightening the screw, which greatly improves pressure accuracy and retraction problem.
Double gear extrusion mechanism: the filament is gripped much more firmly with less deformation thanks to the double drive, so it does not jam so much in the tube, nozzle or hotend
Application: This all-metal dual drive extruder is compatible with Ender 3, Ender 3 V2, Ender 3 Pro, Ender 3 Neo, Ender 3 V2 Neo, Ender 3 Max Neo, Ender 5, Ender 5 Pro, Ender 5 Plus, CR10 series, Voxelab Aquila 3D printers. contains no stepmotorOnly suitable for 3D printers with a motor shaft over 20 mm, please measure the motor shaft before ordering; not suitable for Anycubic or Elegoo or other brands 3D printers

13,98 €
09

UniTak3D

UniTak3D Ender 3 Direct Drive Upgrade Kit Conversion Bracket for Ender 3 V2, Ender 3 Pro and Voxelab Aquila 3D Printer Compatible with BMG Dual Drive & Bowden Extruder & Dual Gear Extruder (Not for

Show more
8.6

Very Good

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

【Supported Flexible Filament】: Compared to Bowden extrusion, this direct drive extrusion greatly improves the print quality of TPU and other flexible materials.
【Stable Operation】The holes of the split type conversion bracket are perfectly aligned, with supports on both sides to keep the center of gravity in the middle and make the structure more stable.
【Easy installation】: No construction volume lost on X, Y or Z axis. No firmware or wiring modification. Simply tear off the original Ender 3 series plate and mount this direct drive upgrade kit.
【Application】: The direct drive conversion plate is suitable for Ender 3 V2, Ender 3 Pro, Ender 3, Voxelab Aquila 3D printer, NOT compatible with Ender 3 Max, Ender 3 Neo, Ender 3 V2 Neo, NOT compatible with Titan extruder. For Ender 3 V2 users, can The following fan the following fan you Print cover (STL:5340394)
Excellent extrusion control: a direct drive extruder improves extrusion and retraction by eliminating the need for Bowden (PTFE) pipe. It offers precise retraction and better printing results.

15,98 €
10

Yosoo Health Gear

Driver Tool, Driver Key Golf, Spike Key, Black Golf Driver Wrench, Replace Golf Shoes Spike Wrench for Driver Shaft Adapter

Show more
8.5

Good

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Tools to install and remove: this golf wrench mainly helps you install and remove bolts or nuts that apply an external force on the handle to tighten or loosen it to achieve the application effect
Lightweight and portable: this golf key torque tool is lightweight, and suitable for carrying at any time, and can solve the problem of installation and disassembly
Inner hex structure: this golf driver wrench has a hex structure inside, which can be applied to screws with any angle to effectively improve your installation efficiency
EVEN FORCE When using this driver golf wrench, the screw on the screwdriver head will not be damaged, because there are 6 contacts between the hex socket screw and the wrench handle, which can produce uniform force
Both ends can be used: both ends of this adjustment wrench can be used. You can choose which end to use according to your actual requirements. This is a good accessory for golfers

12,83 €