Best 3d Printer Controllers 2026

Advertising Disclosure

Last Updated - 22.07.2026

Best Choice

01

BIGTREETECH

BIGTREETECH SKR Mini E3 V3.0 Control Board + TFT35 E3 V3.0.1 Graphic Smart Display Panel Board New Upgrade 3D Printer Parts for Ender 3, Ender3 Pro, Ender 3 V2

Show more
9.7

Exceptional

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Three CNC fans: increase heat dissipation to reduce the temperature of the printer when the device is in operation
Power Output: Extends the SPI output port + 3.3V power supply, the power supply voltage of external SPI sensor +3.3V and +5V are optional, compatible with the motherboard to directly power the peripherals.
Main control chip: STMicroelectronics uses the latest G0 series main control chip STM32G0B1RET6 or STM32G0B0RET6
High heat dissipation: the fan cooler of the drive has been redesigned, the heat dissipation capacity of the drive has been strengthened, and the heat dissipation performance has been significantly improved
Display TFT35-E3 V3.0: This touch panel has a higher compatibility. Users can choose between two operating modes: display mode for serial UART interface and 12864 display mode; the serial port display mode supports two printing modes: SD card and U disk.

106,99 €
Value for Money

02

BIQU

Bigtreetech Octopus Pro V1.0.1(H723) 32bit Control Board Upgrade 550Hz STM32H723ZET6, Support Klipper Marlin High-Speed Printing 8 Stepper Motor Driver DIY & Raspberry Pi Operating Systems

Show more
9.6

Exceptional

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Stepper motor upgraded: supports 8 axis powerful motor drivers, supports 5 V level for stepper motor driver, better performance. support max 60V motor input voltage to inprove motor power,reduce pulse losing. Support STEP/DIR/UART/SPI mode.
Onboard MAX31865: Support 2/4-wire PT100/PT1000 temperature measurement without welding (the soldering resistance can also support 3-wire PT100/PT1000 temperature measurement)
Main control chip: Octopus pro board adopts the ARM Cortex-M7 series, STM32H723ZET6, main frequency up to 550 MHz, processing is more stable and fast. When the chip enters DFU mode, the HE0 and HE2 will start working immediately. To prevent any potential harm or fire caused by prolonged heating of the heater cartridge, it is highly recommended not to enter DFU mode while the motherboard is powered by a 12/24V power supply.
Expanded function interface: Bltouch, resume printing, WiFi, RGB light, filament runout detection. Power shundown, proximity sensor, etc.
About firmware: Supports Marlin and Klipper, the best choice for Klipper high-speed printing, meets the individual needs of DIY users, support operation systems Raspberry Pi / Octoprint.

84,99 €
03

BIGTREETECH

BIGTREETECH SKR Mini E3 V3.0 Control Board with TMC2209 UART Stepper Driver New Upgrade 32Bit 3D Printer Silent Board for Ender 3, Ender 3 Pro, Ender 3 V2 3D Printer

Show more
9.5

Excellent

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Three CNC fans: increase the heat dissipation controllable fan to reduce the temperature of the printer when the device is working; the fan connection must ensure that the voltage specifications of the fan match the motherboard power supply, otherwise the fan has no voltage.
Output power supply: increase the power supply of the SPI output port +3.3 V, external SPI sensor power supply voltage +3.3 V and +5 V are optional, support the motherboard to supply peripherals directly with power.
Main control chip: Use the latest G0 series main control chip from STMicroelectronics STM32G0B1RET6 or STM32G0B0RET6; add a thermistor interface protection circuit to prevent damage to the main control chip.
Heating output: supports the heating hot end and hot bed output. The heater indicator lights up when the hot end or hot bed is correctly connected and turned on. Please connect the wires when switched off, otherwise there may be a static breakdown of the MOSFET and damage to the control board.
Heat sink upgrade: redesign of the drive heatsink, strengthen the heat dissipation capacity of the drive and significantly improve heat dissipation performance; there are 4 TMC2209 silent drivers on the motherboard.
BIGTREETECH offers a 12-month warranty for our SKR MINI E3 V3 motherboard. Please feel free to contact us if you have any problem with our product, we are always ready to help.

52,99 €
04

BIGTREETECH

BIGTREETECH Octopus V1.1 Control Board 32 Bit Compatible Touch Screen of the TFT Series, Supports DIY Clipper Firmware and Raspberry Pi for Voron 3D Printers

Show more
9.4

Excellent

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Special feature: the possibility of installing 5, 12 and 24 volt fans simply by adjusting the jumpers for the respective voltage at the respective connection. The built-in USB type C port and the LAN port are a real plus for any printer
Octopus V1.1:A board for advanced users, it supports 8 step drivers, besides the basic X, Y, Z, e; 4 additional step drivers can be used to add 4 extra extruders to make it a multi-extruder printer, print up to 5 colors in a single job. The ports themselves would also be sufficient for two 3D printers
Note: Due to the price increase of 446ZE chip, only Amazon has 446ZE chip motherboard, other platforms are 407ZE chip, the chip firmware configuration of the new version of 407ZE is different. STM32F407ZE supports Marlin Clipper, but 512KB Flash not enough and there is no custom version for RepRapFirmware
NOT PLUG AND PLAY You probably need to put together your own marlin or clipper for it. Firmware Download: https://github.com/bigtreetech/BIGTREETECH-OCTOPUS-V1.0/tree/master/Firmware If you have any problems, please contact us via Amazon message, we have 24h tech support online.
Motherboard expansion function: support BLTouch, locked rotor detection, shutdown after printing, resume pressure after power failure, CAN bus, U disk function, IIC expansion; simultaneously reserved WiFi interface, PT100 thermistor interface (optional, reserved interfaces only, customers need chip welding, please note), dual Z axis printer
Increase protection function: high-performance MOSFETs to increase heating efficiency and reduce heat generation on the motherboard. Supports "print from SD card" and "USB OTG printing" via the built-in USB-A port.

64,89 €
05

BIGTREETECH

BIGTREETECH SKR Pico V1.0 Customised Control Board Motherboard Designed for Voron V0 3D Printer with Improved Heatsink

Show more
9.1

Excellent

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Technical features: With Raspberry Pi ARM Cortex-MO+ MCU RP2040, Chip Capacitors (MLCC):MURATA Capacitor. The TYPE-C interface is connected to the main control communication. Easy to install and remove the fuse (holder + fuse).
Technical Support Please send us a message via Amazon Message if you encounter any problem. We have a professional technical team to support you.
Parameters: External size: 85 x 56 mm; Installation size: Please refer to BTT SKR Pico V1.0-SIZE.pdf ; Board layer:4; MCU:ARM Cortex-MO+RP2040; Power input: DC 12/24V ; Logic voltage:3.3V ; Motor driver: UART mode of the on-board TMC2209 ; motor motor motor interfac; e:X,Y,Z1,Z2,E; Temperature sensor interface: THO,THB,2-way 100K NTC(RTD); Communication with Raspberry Pi (Raspberry Pi):TYPE-C,UART.
INDUSTRIAL DESIGN The BTT SKR Pico V1.0 adopts an industrial design for heatsink, it makes the overall appearance of the motherboard full sense of technology, while the larger heat dissipation area makes computing more efficient.
Caution: Please use a fan to actively cool the driver chip with a motor driver current greater than 0.8A. Please perform the wiring when the device is switched off. Please make sure the wiring is correct before switching on. Please note that the jumper cap is inserted correctly. Remove the heat sink only if required.

36,99 €
06

Creality

Creality Official Ender 3 Silent Motherboard Upgrade V4.2.7 Motherboard Control Board with TMC2225 Driver 3D Printer Accessories Controller Parts Works with Ender-3 / Pro/Max / 3 V2 / 3 V2 Neo

Show more
9.0

Excellent

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

Super quiet: This Ender 3 upgrade silent board uses TMC2225 drivers. Ultra-quiet system design, so that the machine always runs at low decibels (<50 dB).
Quality assurance: Creality 100% official, all products are original and high quality from 100% quality assurance. Works with Ender-3 / 3 pro / 3 max / 3 V2 / 3neo / 3V2 neo / 3max neo (Note: it has pre-configured the free uniform firmware for Ender 3 printers. If you want to install this board on Ender-3 pro / 3 max / 3 V2 / Ender3 neo / 3 V2 neo / 3 max neo, you need to flash the firmware. If you do not have the firmware, please contact us!)
Plug and play: the motherboard firmware V4.2.7 has been flashed before shipping, it no longer requires an ISP cable and no ISP pin board, making it completely plug and play.
Creality Official Store: We are the official Creality 3D store. We provide professional after-sales support and more than 20 engineers provide 24/7 customer service. Please contact us directly (seller) via "Ask a question".
32-bit and V4.2.7: The V4.2.7 silent board updated by Creality has been updated from 8 bit to 32 bit. It prints more smoothly and the running speed is obviously accelerated.

49,99 €
07

Uadme

MKS TinyBee Control Board 3D Printer 32Bit Silent Board 3D Upgrade 32Bit Motherboard Silent Motherboard with Built-in ESP32 WiFi Support Marlin2.0 Firmware 8MB Chip

Show more
8.9

Very Good

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

【SUPPORT VARIOUS SCREENS】: This is a main control board for 3D printer with built-in ESP32 Wi-Fi, which in addition to the normal LCD2004 and 12864 screen, also supports Marlin2.0 firmware, and also supports MKS MINI12864V3 and MKSTFT serial screen
【8M Byte Chip】: In addition, the controller card for 3D printers has a built-in 8M byte flash memory chip, which provides effective protection for more application scenarios
【32-BIT MICROPROCESSOR】The 3D printer controller is integrated into the ESP32 DOWD V3 chip for Xtensa dual-core 32-bit LX6 microprocessor and supports clock frequencies up to 240MHz
Powerful and versatile: the 32-bit motherboard uses the ESP32 WROOM 32U module, an embedded dual-core 32-bit high-speed MCU, the clock is up to 240 MHz. And integrate WiFi, Bluetooth module, update the firmware via USB, you can connect WiFi and website to control the print
Back EMF protection: VEXP has developed a protection circuit for the counter-EMF generated by the stepper motor, which significantly reduces the damage to the motor driver of the 3D printer control board

29,99 €
08

BIGTREETECH

BIGTREETECH SKR V1.4 Turbo 32bit Controller Panel Board for 3D Printer Compatible With12864LCD/ TFT24 Support 8825/TMC2208/Tmc2130

Show more
8.8

Very Good

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

5) Support 2.4, 2.8, 3.5 inch colour touch screen, support LCD2004, LCD12864 screen; update the configuration firmware via an SD card, and operate it easily, conveniently and efficiently. URL for open source information on BTT SKR V1.4: https://github.com/bigtreetech/BIGTREETECH-SKR-V1.3/tree/master/BTT%20SKR%20V1.4
4) The integrated TMC-controlled SPI working mode and UART working mode as well as the integrated DIAG function pins are convenient for customers to use, eliminating the complicated wiring process that can be used by simply removing and inserting the jumper cap; support functions such as continuous power on, material detection, shutdown after power off.
3) With the 32-bit main control chip of Cortex-M3 series LPC1769 of the ARM class with 120 MHz, the performance is greatly improved. Equipped with a highly modular open source Marlin 2.0 firmware suitable for users for DIY and secondary development. Board shows tmc connection error? Please turn on the printer.
2) "Bed Temp Error"? There may be a problem with the thermistor or the connection of the hot bed. Try replacing the thermistor. If this still does not work, check whether the voltage and resistance of the thermistor port TB of the hot bed are normal.
1) The SD slot does not work? Possibly the format of the SD card is incorrect or the SD card slot is damaged. The SD card must be in the FAT32 system. Do not forcibly pull out or insert the SD card. This can easily lead to damage the SD card slot.

57,99 €
09

STEEIRO

TB6600 Stepper Motor Driver 4A 9V-42V 42/57/86 Type 2-Phase 4-Phase Stepper Motor Driver Controller for 3D Printer Printer/CNC (Pack of 4)

Show more
8.7

Very Good

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

This driver is an updated version of TB6600, and the subdivision has been increased to 32 subdivisions suitable for high subdivision purposes.
Semi-automatic power locking function for energy saving, and built-in temperature protection and overcurrent protection. H-bridge bipolar constant phase flow driver, 2/4 phase hybrid.
It is suitable for all small automatic devices and small parts such as engraving machines, marking machines, cutting machines, laser photocopying, plotters, CNC machine tools, etc.
DC 9V-42V power supply (recommended 12-24V), and the maximum output current is 4.0A (peak, in 100ms).
Applicable stepper motor: 42, 57, 86 type 2 phase 4 phase (4 wire 6 wire 8 wire).

28,99 €
10

OSOYOO

OSOYOO 3D Printer Parts MKS TS35-R 3.5 Touch Screen for DLC32 Offline Controller

Show more
8.6

Very Good

Our rankings are cleverly generated from the algorithmic analysis of thousands of customer reviews about products, brands, merchant’s customer service level, popularity, trends and more. The rankings reflect our opinion and should be a good starting point for shopping.

Show more
Main highlights

TS35-R is only compatible with MKS DCL32 offline controller mainboard
Network operation for DLC32 control board.
3.5 inch touch screen, simple operation interface and high sensitivity

40,95 €